XL2411Z, XL2420Z: AMA low reduces the inverse ghosting (helps a lot) but does not turn it into normal ghosting. *XL270Z specific feature-undocumented - AMA low setting -removes ALMOST ALL INVERSE GHOSTING, adds normal ghosting, which can be removed by lowering the contrast setting!
#Benq projector service menu update#
This monitor needs a firmware update to force single strobe for refresh rates 60-85hz. This monitor will double strobe lower than 100hz, as the single strobe override is missing from the service menu. VT 1825 works at 2560x1440, and can be increased to VT 1852 by lowering the horizontal total.
Zowie XL2735 uses the same or a modified revision of the XL2730 scaler, Realtek 2796BF, and vertical total tweaks to lower strobe crosstalk work again. The XL2730Z will NOT strobe in sync at ANY refresh rate lower than 120hz! Note: the XL2730Z does not have the single strobe setting. (May or may not apply to XL2430T and XL2730Z). You can save a preset to a gamer preset by holding down the preset button for 8+ seconds. You can enter STANDARD MODE from any other mode preset, by holding down the top (back/exit) button on the s-switch, for 8 seconds+, then releasing. In the service menu use button #5 (up), #4 (down) and #3 (select) to navigate the menuĥ) For the XL2411Z (also the older XL2411T), it's button #2 (down button) for 5 seconds with power off, instead of button #4, then press power on+button #2 The lights will flash, and when the monitor has turned on press button #2 once to enter the service menu. While holding this button, press the power button to turn the monitor on. To enter the service menu (XL2420Z, XL2430T, XL2720Z, XL2730Z, XL2735, XL2540, XL2546) with the single strobe (for single strobing refresh rates lower than 100hz-ONLY ON THE XL2720Z and older Benq blur reduction monitors-the REALTEK versions do NOT have the Single Strobe override setting), strobe duty (Intensity), strobe phase (Area) and other settings: Turn off the monitor, then press and hold menu button #2 from the bottom. The factory menu on the newer Benq monitors (Realtek 2796BF) has many more options than on the Mstar chipset versions. The XL2730Z only has 4 or 5 adjustments possible in OD gain.
The XL2735, XL2540 and XL2546 allow very fine adjustments of overdrive via the FACTORY MENU, by changing the overdrive gain from many different values (may be 100, may be 256 in hexadecimal). It has been reported that the XL2540 and the XL2546 also have the same service menu and factory menu codes. if you are brave enough to mess around in the "Factory" menu with the Bank Scaler ADDR (address) and VALUE (data) options) and someone discovers something, let us know. If anyone ever find some sort of undocumented hack or setting (e.g. None of the Realtek models single strobe any lower than 100hz (and the original release XL2730Z had broken sync strobe at 100hz making it unusable). The regular service menu has the HDMI, DVI HPD, Internet Cafe and Single Strobe on/off settings on the MSTAR models. Some people have reported an inability to enter the regular service menu on the XL2411P.
There are microstick models as well, and I do not know how they work.Ģa) if nothing happens at all when the power button is pressed (this is most common after a firmware update or an AC hard power off), press power to give the monitor current, then after you get a display, power the screen off again, and then start sequence 1 again.Ģb) XL2420Z, XL2430T, XL2720Z and XL2730Z, XL2735 (reported also on XL2546, XL2540): buttons 3 and 4 with power off for 5+ seconds, and then pressing the power button while continuing to hold the buttons down, will unlock the factory menu. On vertical layout models (XL2420Z, XL2720Z, etc), button 1 is on the top.
On horizontal layout buttons (DyAc models, etc), button 1 is on the left.
#Benq projector service menu how to#
Since there isn't any clear information on how to enter the service/factory menus, in one clear spot, here it is.Ģ) XL2411Z only: hold button #3 and button #5 with the power off, for 5 seconds, then press power while still holding them down. *Now with pictures of AMA low in action*!
0 kommentar(er)
